Amplifier
From Wikipedia, the free encyclopedia
For the British rock band of the same name, see Amplifier (band)
An amplifier can be considered to be any device that uses a small amount of energy to control a source of a larger amount of energy, although the term today usually refers to an electronic amplifier. The relationship of the input to the output of an amplifier — usually expressed as a function of the input frequency — is called the transfer function of the amplifier, and the magnitude of the transfer function is termed the gain.
Contents |
General characteristics of amplifiers
Most amplifiers can be characterised by a number of parameters.
Gain
How much an amplifier increases the signal level is called the gain. This is usually measured in decibels (dB). Mathematically speaking, the gain is equal to the output level divided by the input level.
Output dynamic range
This is the range usually quoted in dB between the lowest useful output and the largest useful output level. Since the lowest useful level is limited by output noise, this is quoted as the amplifier dynamic range.
Bandwidth and rise time
The bandwidth (BW) of an amplifier is usually defined as the difference between the lower and upper half power points. This is therefore also known as the −3 dB BW. Bandwidths for other response tolerances are sometimes quoted (−1 dB, −6 dB etc.).
As an example, a good audio amplifier will have a −3 dB BW from around twenty hertz to about twenty kilohertz (the range of normal human hearing).
The rise time of an amplifier is the time taken for the output to change from 10% to 90% of its final level when driven by a step input. For a Gaussian response system (or a simple RC roll off), the rise time is given by:
Tr = BW/0.35, where BW is in Hz and Tr is in seconds.
Settling time and aberrations
Time taken for output to settle to within a certain percentage of the final value (say 0.1%). This is usually specified in oscilloscope vertical amplifiers and high accuracy measurement systems.
Slew rate
Slew rate is the maximum rate of change of output variable, usually quoted in volts per second (or microsecond).
Sine wave distortion
The properties of amplifier circuits distort the signal. This distortion comes in several forms including harmonic distortion and intermodulation distortion.
Harmonic distortion is fairly easy to measure. The amplifier output is connected to a spectrum analyzer, (a device which graphs frequency against amplitude). Then a pure tone is applied to the amplifier input. Typically a sinusoidal signal of 1 kHz is used. The largest signal on your analyzer should be the input signal at 1 kHz. You will sometimes see humps at even intervals along the graph at even multiples of that base signal. These are the harmonics. The total harmonic distortion (THD) is the sum of these components relative to the signal.
Noise
How much noise is introduced by the amplification process? This is an undesirable thing that is the inevitable result of the electronics devices and components. It is measured in either decibels or the peak output voltage produced by the amp when no signal is applied.
Efficiency
How much of the input power is usefully applied to the amplifier's output? Class A amplifiers are very inefficient, in the range of 10–20% with a max efficiency of 25%. Modern Class AB amps are commonly between 35–55% efficient with a theoretical maximum of 78.5%. Commercially available class D amplifiers have reported efficiencies as high as 97%. The efficiency of the amplifier limits the amount of total power output that is usefully available. Note that more efficient amps run much cooler, and often do not need any fans even in multi-kilowatt designs.
Electronic amplifiers
- Main article: electronic amplifier
There are numerous types of electronic amplifiers, depending upon the application.
One common type of amplifier is the electronic amplifier, commonly used in radio and television transmitters and receivers, high-fidelity ("hi-fi") stereo equipment, microcomputers and other electronic digital equipment, and guitar and other instrument amplifiers. Its critical components are active devices, such as vacuum tubes or transistors.
Power amplifier classes
Amplifiers are commonly classified by the conduction angle (sometimes known as 'angle of flow') of the input signal through the amplifying device; see electronic amplifier.
- Class A
- Where efficiency is not a consideration, most small signal linear amplifiers are designed as class A, which means that one active device amplifies all portions (360deg) of the input signal.
- Class B
- In Class B, each output device conducts for exactly 180 deg (or half wave) of the input signal.
- Class AB
- Class AB transmits between 180 and 360 degrees selected by the amplifier creator. These classes are usually used in efficient low frequency amplifiers (such as audio and hi-fi) owing to their relatively high efficiency, or other designs where both linearity is important and efficiency is important (cell phones, cell towers, TV transmitters).
- Class C
- Another popular RF amplifier class is Class C, which means that they amplify less than 180° of the input signal. The signal is restored to almost sinusoidal shape by the tuned circuit, and efficiency is higher than A, AB, or B classes of amplification, but linearity is very poor.
- Class D
- Class D amplifiers are usually dedicated to audio, and base on PWM (Pulse Width Modulation) techniques to achieve a very high power efficiency (more than 90% in modern designs). Formerly used for subwoofers only due to their limited bandwidth and relatively high distortion, the evolution of semiconductor devices has made possible the development of very high fidelity, full audio range Class D amplifiers, with S/N and distortion levels even better than their linear counterparts.
- Other classes
- There are several other amplifier classes, although they are mainly combinations of the previous classes. For example, Class H and Class I amplifiers are marked by variation of the supply rails (in discrete steps or in a continuous fashion, respectively) following the input signal. Wasted heat on the output devices can be reduced as excess voltage is kept to a minimum. The amplifier that is fed with these rails itself can be of any class. These kinds of amplifiers are complicated and have some problems that limit their applications.
Vacuum tube (valve) amplifiers
- Main article: valve amplifier
Valve amplifiers are widely, but not always correctly, associated with the valve sound. Some claim this sound has more to do with the circuit topology and circuit design of the amplifier, than to the use of valves rather than transistors as the active gain devices. In the earlier years of audio, vacuum tubes filled the active device role.
Transistor amplifiers
- Main articles: transistor, bipolar junction transistor, MOSFET
The essential role of this active element is to magnify an input signal to yield a significantly larger output signal. The amount of magnification (the "forward gain") is determined by the external circuit design as well as the active device.
Many common active devices in transistor amplifiers are bipolar junction transistors (BJTs) and metal oxide semiconductor field-effect transistors (MOSFETs).
Applications are numerous, some common examples are audio amplifiers in a home stereo or PA system, RF high power generation for semiconductor equipment, to RF and Microwave
Operational amplifiers (op-amps)
- Main articles: operational amplifier, instrumentation amplifier
An operational amplifier is a solid state integrated circuit amplifier which employs external feedback for control of its transfer function or gain.
Video amplifiers
These are used to deal with video signals and have bandwidths of about 5 MHz. Certain requirements on step response and overshoot are necessary in order for acceptable TV images to be presented. The design of high bandwidth video amplifiers is a difficult undertaking.
Oscilloscope vertical amplifiers
These are used to deal with video signals to drive an oscilloscope display tube and can have bandwidths of about 500 MHz. THe specifications on step response, rise time, overshoot and abberations can make the design of these amplifiers extremely difficult. One of the pioneers in high bandwidth vertical amplifiers was the Tektronix company.
Distributed amplifiers
These use a transmission lines to temporally split the signal and amplify each portion separately in order to achieve higher bandwidth than can be obtained from a single amplifying device. The outputs of each stage are combined in the output transmission line. This type of amplifier was commonly used on oscilloscopes as the final vertical amplifier. The transmission lines were often housed inside the display tube glass envelope.
Microwave amplifiers
Travelling wave tube (TWT) amplifiers
Used for high power amplification at low microwave frequencies.
Musical instrument amplifiers
See main page: instrument amplifier.
Audio amplifier
An audio amplifier is usually used to amplify signals such as music or speech.
- Main article: Audio amplifier
Other amplifier types
Carbon microphone
One of the first devices to amplify signals was the carbon microphones. By channeling a large electric current through the compressed carbon granules in the microphone, a small sound signal could produce a much larger electric signal. The carbon microphone was extremely important in early telecommunications, analog telephones in fact work without the use of any other amplifier. Before the invention of electronic amplifiers, mechanically coupled carbon microphones where also used as amplifiers in telephone repeaters for long distance service
Magnetic amplifier
- Main article: magnetic amplifier
A magnetic amplifier is a transformer-like device that makes use of the saturation of magnetic materials to produce amplification. It is a non-electronic electrical amplifier with no moving parts. The bandwidth of magnetic amplifiers extends to the tens of kilohertz.
An Amplidyne or Rototrol is a rotating machine like an electrical generator that provides amplification of electrical signals by the conversion of mechanical energy to electrical energy.
Optical amplifiers
- Main article: Optical amplifier
Optical amplifiers amplify light through the process of stimulated emission.
Miscellaneous types
- There are also mechanical amplifiers, such as the automotive servo used in braking.
- Relays can be included under the above definition of amplifiers, although their transfer function is not linear (that is, they are either open or closed).
- Another type of amplifier is the fluidic amplifier, based on the fluidic triode.
See also: electronic amplifier, low noise amplifier, preamplifier, satellite in-line amplifier.
See also
External links
- 60 Watt RF Amplifier Solid state RF power amplifier using IRF840. Simple and easy to construct. IRF840 can handle a maximum power output of 125 Watts.
- The Audio Circuit — Information on and user reviews of loudspeakers, headphones, amplifiers, and playback equipment.
- Car Audio — Talk about Car Audio amplifiers and other mobile electronics.
